JESD22 A115 PDF
Curve Tracing Capability. • Six Separate V/I Supplies. • Latch-Up Testing with 64k /pin. ESD and Latch-up Test Services. MM (30V – 2kV). • EIA/JESDAC. JESDA is a reference document; it is not a requirement per JESD47 ( Stress Test Driven Qualification of Integrated Circuits). Machine. AEDR and AEDR Reflective Surface Mount Optical Encoder Reliability Data Sheet Description Failure Rate Prediction The following.
|Published (Last):||21 July 2005|
|PDF File Size:||14.61 Mb|
|ePub File Size:||4.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
This new test method describes a uniform method for establishing charged-device model electrostatic discharge withstand thresholds.
Please see Annex C for revision history. Reaffirmed May JEP Oct This document was written with the intent to provide information for quality organizations in both semiconductor companies and their customers to assess and make decisions on safe ESD CDM level requirements.
ELECTROSTATIC DISCHARGE (ESD) SENSITIVITY TESTING MACHINE MODEL (MM)
This confidence interval is based on the statistics of the distribution of failures. In June the formulating committee approved the addition of the ESDA logo on the covers of this document. In this regard, the document’s purpose is to provide the necessary technical arguments for strongly recommending no further use of this model for IC qualification.
Registration or login required.
The published document should be used as a reference to propagate this message throughout the industry. This document was written with the intent to provide information for quality organizations in both semiconductor companies and their customers to assess and make decisions on safe ESD level requirements.
Standards & Documents Search | JEDEC
Filter by document type: In the case of zero failures, one failure is assumed for this calculation. The failure rate of semiconductor devices is determined by the junction temperature of the device.
Catastrophic failures are open, short, no logic output, no dynamic parameters while parametric failures are failures to meet an electrical characteristic as specified in product catalog such as output voltage, duty or state errors. Displaying 1 – 7 of 7 documents. AVEN – April 27, This particular distribution is commonly used in describing useful life failures.
The relationship between ambient given by the following: One of many examples is a device sliding down a shipping tube hitting a metal surface. Discharges to devices on unterminated circuit assemblies are also well-modeled by the CDM test. This report is the first part of a two part document. Avago tests parts at the absolute maximum rated conditions recommended for the device.
Results of such calculations are shown in the table below using an activation energy of 0. Solid State Memories JC The actual performance you obtain from Avago parts depends on the electrical and environmental characteristics of your application but will probably be better than the performance outlined in Table 1. Failures are catastrophic or parametric. Part I will primarily address hard failures characterized by physical damage to a system failure category d as classified by IEC The purpose objective of this standard is to establish a test method that will replicate HBM failures and provide reliable, repeatable HBM ESD test results from tester to tester, regardless of component type.
Over the last several decades the so called “machine model” aka MM and its application to the required ESD component qualification has been grossly misunderstood. The document is organized in different sections to give as many technical details as possible to support the purpose given in the abstract. The assumed distribution of failures is exponential. Show 5 results per page.
The scope of this JEDEC document is to present evidence to discontinue jeds22 of this particular model stress test without incurring any reduction in the IC component’s ESD reliability for manufacturing. CDM ESD events not only reduce assembly yields but can also produce device damage that goes undetected by factory test and later is the cause of a latent failure.
Data subject to change. This standard establishes the procedure for testing, evaluating, and classifying components and microcircuits according to their susceptibility sensitivity to damage or degradation by exposure to a defined human body model HBM electrostatic discharge ESD. Search by Keyword or Document Number.
Standards & Documents Search
It will be shown through this document why realistic modifying of the ESD target levels for component level ESD is not only essential but is also urgent. Multiple Chip Packages JC Quality and Reliability of Solid State Products filter.
This document was written with the intent to provide information for quality organizations in both semiconductor companies and their customers to assess and make decisions on safe ESD CDM level requirements.