ISO 17660-2 PDF

0 Comments

ISO (E). PDF disclaimer. This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file. Buy ISO (R) WELDING – WELDING OF REINFORCING STEEL – PART 2: NON LOAD-BEARING WELDED JOINTS from SAI. ILNAS-EN ISO Welding – Welding of reinforcing steel – Part 2: Non load- bearing welded joints (ISO ). Soudage.

Author: Vudolar Vugal
Country: Jordan
Language: English (Spanish)
Genre: Health and Food
Published (Last): 26 September 2018
Pages: 166
PDF File Size: 12.26 Mb
ePub File Size: 5.57 Mb
ISBN: 348-9-26261-782-8
Downloads: 35768
Price: Free* [*Free Regsitration Required]
Uploader: Talkis

It specifies requirements for materials, design and execution of welded joints, welding personnel, quality requirements, examination and testing.

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. JavaScript seems to be disabled in your browser. Annex D is an example form and should be used where appropriate. You must have JavaScript enabled in your browser to utilize the functionality of this website.

Taking these issues into account, it is apparent that both the welder and the welding coordinator require a specific level of skill and job knowledge and that special procedures for quality assurance need to be adopted. ISO consists of the following parts, under the general title Welding — Welding of reinforcing steel: In addition, dirt, grease, oil, moisture, rust, loose scale, and paint shall be removed from the area to be welded. Whenever the welding conditions, e.

It is identical with ISO For welding processes 21 and 23, acceptance criteria in accordance with ISO apply. The welding coordination personnel shall be responsible for the quality of welded reinforcing steel joints in the workshop as well as on the site.

  EL DISFRAZ JANINA PEREZ PDF

Our offices will be closed from December 24, to January 2, inclusive. Revisions British Standards are updated by amendment or revision. NOTE Agt is measured over the weld area.

Various BSI electronic information services are also available which give details on all its products and services.

Assemblages non transmettants ISO At the end of the training period, the welders shall weld a relevant number of test specimens e. The welding coordination personnel shall take remedial measures in cases of imperfections. One of the principal differences between BS and this standard is that BS offered more practical guidance on the iiso process issues, some of these issues have been highlighted in the National Annex and further guidance can be found in parts 1 to 3 of BS EN The carbon equivalent value CEVthe manufacturing route and the delivery conditions shall be determined before welding.

ISO/DIS – Welding — Welding of reinforcing steel — Part 2: Non load-bearing welded joints

Welder and welds shall be suitably protected against environmental factors, such as wind, rain and snow. Health care technology It is the constant aim of BSI to improve the quality of our products and services. Valid Buy this standard. The welds shall not influence significantly the full load-bearing capacity and ductility of the bars, and the welding procedure may not cause embrittlement of the material. All test pieces shall be visually inspected prior to testing.

  HIZB SAIFI PDF

NBN EN ISO 17660-2

Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Accept and continue Learn more about the cookies we use and how to change your settings. Standards are also available from the BSI website at http: The welding coordinator shall evaluate those welders under his supervision. For welded joints in reinforcing steel made by arc-welding processes, the quality level D applies for surface imperfections, as appropriate, in accordance with ISO except for undercuts, where quality level C applies.

We izo cookies to make our website easier to use and to better understand your needs. This standard is best used in www. Arc welding ISOSpecification and qualification of welding procedures for metallic materials — Welding procedure specification — Part 5: These welds 117660-2 often referred to as tack welds.

You have 16760-2 items in your shopping cart. It specifies requirements for materials, design and execution of welded joints, welding personnel, quality requirements, examination and testing.

BS EN ISO 钢筋的焊接-非承载焊缝 – MBA智库文档

Energy and heat transfer engineering Shipbuilding and marine structures Reinforcing steel bars are produced by a number of process routes and usually have a ribbed profile.

The length of the weld l and throat thickness a depend on the application, and shall be in accordance with the WPS. Report error on page. Contact the Information Centre.