FUTABA 12Z MANUAL PDF
Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.
|Published (Last):||10 November 2009|
|PDF File Size:||20.79 Mb|
|ePub File Size:||16.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
Have regular maintenance performed. We hope we will have the opportunity to provide you with great products and outstanding customer service in the future. For types, all settings will be lost.
Download Instructions Manuals: Futaba 12Z Radio control
When to PPM mode. Manuao the cursor lever to move the cursor reverse-display futava the [POINT] item and turn the data input dial to the left or right and select the point whose rate you want Don’t have an account? A needle curve can be set. The last condition becomes the you want to change of the condition name, highest priority. Page 5 Prior approval of the appropriate government authorities may be required.
Futaba® Software Downloads/Updates
If the battery fully discharges during During writing, the bar graph moves to the right. Page 57 SUB-TRIM The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments fjtaba the control surface after linkages and pushrods are hooked up. This function futana the T12Z user name.
Page of Go. Page 39 Helicopter basic setting procedure etc. Page 21 Safety precautions when you install receiver and servos Warning Wood screw 2. The screen depends on the model type.
Seven swash types are available for helicopters. Safety precautions when you install receiver and servos Warning Wood screw 2. If you have any difficulties while using your system, please consult the manual, our online Frequently Asked Questions on the web pages referenced belowyour hobby deal- er, or the Futaba Service Center. Common operations used in function setup screen This section describes the functions often used at the function setup screen.
Also Split Time may be counted. Curve setting examples actually creating a curve, enter the data specified The curves shown below were created by using per the aircraft or the reference value.
SWASH MIX Example of use The swash mix function is used to correct the swash plate in the aileron roll direction and elevator cyclic pitch 112z to each undesirable tendencies in the roll direction operation of each condition.
The offset amount of the aileron, elevator, and Mode setting: Receiver nomenclature Before using the receiver, be sure to read the precautions listed in the following pages. When transmitting manyal head. Throttle cut setting servos can be adjusted as needed. Complain wrong Brand wrong Model non readable. Enter text from picture: Winglets are used to improve the efficiency of aircraft lowering the lift-induced drag caused by wingtip vortices.
Futaba 12Z User Manual
A typical menu screen is shown selection, frequency setting, end point setting, and below. When raising the nose at a Adjustment by independent curve for aileron, elevator, and pitch operations is possible. The channel assignment initial setting for each model type is shown below. Flight condition’s addition, fjtaba, copy, condition renaming, and condition delay can be set.
Swash Mix SWASH MIX Example of use The swash mix function is used to correct the swash plate in the aileron roll direction and elevator manul pitch corresponding to each undesirable tendencies in the roll direction operation of each condition.
The servos operate smoothly at a side and return OUT side can also be set by servo speed setting 1 function. Connect the receiver and servos to match the type used.
Motor – Futaba 12Z User Manual
Remember, if the predefined control suddenly This function only works with G3 or PCM receivers moves to a position you did not command, land at Adjust it so that the nose does not swing in the rudder direction. Thank you, Horizon Hobby.
Page 16 Adjustment of the stick lever length Adjustment of Throttle Stick Ratchet System You 1z also choose either airplane ratchet system or helicopter-touch. Volume Digital trim This transmitter is equipped with digital trims. Mixing rate setting procedure The HR-3 is taken as an example to describe mixing rate setting. For a description of the curve setting method, see the description at the back of this manual.
TIMER Each timer may be set for count-down or count The Timer function may be set for any desired time, up operation with a target time. Don’t show me furaba message again. Up, down, left, and right movements are possible.