FLUKE 5500A MANUAL PDF

0 Comments

Each Fluke product is warranted to be free from defects in material and The A Manual Set provides complete information for operators and service or. Warning If the A Calibrator is operated in any way not specified by the A Operators Manual or other documentation provided by Fluke, protection. View and Download FLUKE A operator’s manual online. Multi-Product Calibrator. A Test Equipment pdf manual download.

Author: Moogulrajas Mazuramar
Country: Yemen
Language: English (Spanish)
Genre: Software
Published (Last): 21 November 2016
Pages: 54
PDF File Size: 10.68 Mb
ePub File Size: 15.33 Mb
ISBN: 404-4-85102-640-1
Downloads: 77642
Price: Free* [*Free Regsitration Required]
Uploader: Meztishicage

Page Waveform command Set the waveforms for ac outputs.

Readjust A90R13 if necessary to keep the edge signal at the reference level. V dc Value V dc Value V dc For all ranges, the maximum charge and discharge current is mA pk or 30 mA rms. If only one amplitude is supplied, the A Calibrator sources a single output.

All calibration is done with the covers on, using software calibration constants. The blue softkey under Output Z toggles the impedance between 50 Q.

5500A Operator Manual

This cable eliminates the need for flume four-wire connection. Lift off the guard box cover using the finger pull on the rear edge of the cover.

The green indicator on the scope key will be illuminated when the SC is enabled. AC Voltage into a 50 Load. Setting Dc Current Output Page 63 Introduction Turn the A Calibrator power on. Press the reset key.

  CHEIKH AL ALBANI PDF

Adjusting the Output Signal The A provides several ways to change the settings for the output signal during calibration. Remove the power switch pushrod. If this warning occurs recheck the setup and carefully re-enter the reading insuring proper nanual i.

A calibration routine that prompts you through the entire procedure is built into the A.

Fluke Calculator A/COIL User Guide |

Testing The Ieee Flhke 1. Adjust the DSO horizontal scale and main time base position until the pulse signal spans between half and the full display. Page 62 A Operator Manual Note that the DDS assembly works together with the Current assembly to generate current outputs.

Install a copper short circuit in tluke front panel TC connector total instrument zero only. Parts, product repairs and services are warranted for 90 days.

Fluke a – Sc Multi-product Calibrator | eBay

The two reference guides and the Getting Started manual are shipped with the unit. Page The memory holds calibration constants and setup parameters. The parts lists give the following information: The A produces calibration flkke of the following functions and ranges: Enter the mnaual reading into the A when prompted by the A.

As soon as the spur is minimized, stop rotating Rl. Thermocouple Measuring Accuracy Test. Adjust the amplitude using the Calibrator Mainframe front panel knob until the A reference deviation matches the 50 kHz reference within ppm.

  DEJAME QUE TE CUENTE BUCAY PDF

Page 18 A Operator Manual As soon as the spur is gone, stop rotating R Table Of Contents Accessories Check the part number of your board before you begin aberration adjustments.

An amplifier stage before the final amplifier. Follow the same procedure for testing other amplitudes, only compare results against the flatness specification listed in Table Time Marker Function Specifications Thermocouple Measuring Accuracy The Thermocouple Measuring Accuracy test checks the accuracy of the thermocouple measuring circuitry.

Before you begin verification, you may wish to review all of the procedures in advance to ensure you have the resources to complete them. Leveled Sine Wave Amplitude Calibration.

It is possible to achieve a very flat manuql close to the horizontal center, but if the peak is too high or too low, then the aberrations will not be properly adjusted. Suspect ICs are U16 and U5. This notice explains how you can minimize the chances of destroying such devices by: Command Summary by Function Allow the A reading to stabilize, then enter the reading into Column A of the table.