DRYPIX 4000 SERVICE MANUAL PDF

0 Comments

HANDLING THIS SERVICE MANUAL About This Service Manual n. Scope This Service Manual applies to the Fuji Medical Dry Laser Imager DRYPIX Service Technicians PACS / DR / CR / Digital Forum Drypix Service Manual CARLOS RUEDA Innovacion Tecnologica Hello, I am trying. View and Download FujiFilm DRYPIX service manual online. DRYPIX Printer pdf manual download.

Author: Mumuro Fenrihn
Country: Tunisia
Language: English (Spanish)
Genre: Travel
Published (Last): 5 March 2010
Pages: 217
PDF File Size: 14.60 Mb
ePub File Size: 12.60 Mb
ISBN: 358-2-42944-984-4
Downloads: 49550
Price: Free* [*Free Regsitration Required]
Uploader: Kajit

MC Remove the tray. Secure the cable with the clamp. Loosen the fixing screws of the magnet.

Page 52 Push down the plate, and with an approximately 50 mm space between the plate and stopper, push the suction cup against the film. Film Positioning Assembly lower Remove the grip position detection sensor bracket. This site uses cookies.

Drypix Service Manual – Service Technicians Forum

Test Contents Mechanical Output test pattern films to make sure that there are no mechanical transportation errors or abnormal sounds. Page 87 Remove the sub-scanning unit fixing bracket, and reinstall it to its original position. Film Positioning Motor upper md5 Remove the upper conveyor unit. Cleaning Roller Grip Release Motor md4 Rotate the worm gear of the cleaning roller grip release motor MD4 in the arrow direction shown in the figure with the hand so that it grips the cleaning roller.

  ASTADASA PURANAS IN TELUGU PDF

Remove the film positioning assembly lower. Heat Development Unit Remove the film release unit. Page 56 MC Remove the screws securing the sub-scanning unit. Geometry Output test pattern films and measure the specified horizontal and vertical length to confirm it is within specifications.

The screws painted in yellow must be adjusted after the installation of parts. Page 20 MC Remove the tray. EPS Reinstall the sub-scanning unit fixing bracket at the position shown below.

MC Remove the cooling fan assembly. When the data transfer dryipx completed, the [File transfer is completed. Table of Contents Add to my manuals Add.

DryPix Operation Manual. Remove the suction cup arm. Install the inside belt first and then the top and bottom belts. Page 91 Rotate the positioning screw in the clockwise drupix counterclockwise direction and adjust. Like the DryPix andthis unit also features micron high resolution printing.

When reinstalling the adiabatic cover, do not sandwich the thermistor cable. Page 94 26 x 36 cm size 20 x 25 cm size Removing Procedure Insert the shutter into the film tray. Removal Drive Cam Remove the gear 1 and gear 2. EPS Reinstall in the reverse order of removal.

Forums Documents and Manuals. Insert the sub-scanning unit into the equipment, and temporarily secure with the screws.

Rotate the positioning screw in the clockwise or counterclockwise direction and adjust. MC Remove the screws securing the sub-scanning unit. Page Remove the heat development unit. Mechanical Jamming, Abnormal Sound 2.

  GORDON ALLPORT TEORIA DA PERSONALIDADE PDF

Remove the conveyance driving roller lower. Remove the belt cover. Remove the upper conveyor unit. Remove the sub-scanning unit fixing bracket, and reinstall it to its original position.

service manual

Enter text from picture: Rotate dryix worm gear of the cleaning roller grip release motor MD4 in the arrow direction shown in the figure with the hand so that it grips the cleaning roller. Place the tip in front and rdypix the right rail of the tray loading unit on the aperture of the tray loading unit, tighten the rail temporarily with the screws. However, perform the following when securing the sub-scanning unit into the equipment. Artifacts Output test pattern films to make sure that there are no clinically significant artifacts, such as banding, scratch, fog etc.

Push down the plate, and with an approximately 50 mm space between the plate and stopper, push the suction cup against the film.