DATASHEET XR 2206 PDF
XR datasheet, XR pdf, XR data sheet, datasheet, data sheet, pdf, Exar, Monolithic Function Generator. Monolithic Function Generator IC – XR Data Sheet (current) [ KB ] The XR is a monolithic function generator integrated circuit capable of. XR Voltage-controlled Oscillator. FEATURES D Excellent Temperature Stability (20ppm/°C) D Linear Frequency Sweep D Wide Sweep Range (
|Published (Last):||14 July 2010|
|PDF File Size:||14.30 Mb|
|ePub File Size:||5.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
Headphone amplifier is small enough to fit in Altoids tin box, and thanks to low power consumption may be supplied from a single 9V battery. Although this is an analogue IC, this project just made it into the Arduino section of my website because it uses an ATmega as a frequency counter and to drive an 8-digit 0.
It is an irreplaceable tool for troubleshooting and repairing electronic equipment by determining performance and health of electrolytic capacitors. The circuit includes an auto ranging as well as reset switch and produces very accurate and stable readings. The frequency is changed by using a variable resistor.
The meter is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored.
But there are some points that could improve it take to build an almost professional function generator.
You can control lights, fans, AC system, computer, printer, amplifier, robots, 206 door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
Function Generator with XR Instead of the sine wave output is obtained after opening of S1 a triangular output dqtasheet. A common function generator provides sine, for example, triangular and square waves. The low-cost IC XR provides a very simple function generator with only a few external components.
Arduino – XR Function Generator
It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as datasjeet, radio receivers, transmitters, function generators, crystals, etc. The capacitor C and the power to determine the frequency at pin 7. On the board, the outputs of the circuit were placed in small wire loops, where the signals can be picked up directly with alligator clips. Arduino Prototype datashset all standard through-hole components for easy construction, two of which are hidden underneath IC socket.
It also analyzes transistor’s characteristics such as voltage and gain.
XR Datasheet(PDF) – Exar Corporation
It can be connected to any type of stereo audio source such as iPod, Computer, Laptop, 226 Player, Walkman, Television, Satellite Receiver, Tape Deck or other stereo system to transmit stereo sound with excellent clarity throughout your home, office, yard or camp ground.
XR data sheet provides complete basic circuit for a simple function generator. This LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils and inductors.
It requires an operating voltage of 12 V and delivers sine and square wave signals.
datasheeg Thus, only a frequency ratio of 1 was chosen toso ratasheet finer adjustment is possible. With the frequency-determining capacitor of 0. Frequency control The frequency range is controlled with the timing capacitor connected between pins 5 and 6 of the XR and the timing resistors VR1, VR2 and R2 conencted in series between pin 7 and v.
A sine-shaping network makes the triangular signal of the VCO, a sinusoidal signal that can be picked up at the pin 2.
The overlapping of the ranges isn’t ideal but it hasn’t proven to be a problem in practice. With the component values shown above, the overlapping frequency ranges are shown in the following table: The additional output at pin 11 also delivers a square wave with the same frequency. The output waveforms can be both amplitude and frequency modulated.
The sample design renounces everything that is not absolutely necessary. Although I’ve seen circuits and even commercial project kits claiming several MHz frequency range, in practice I think somewhere around kHz or kHz maximum frequency is more realistic for these ICs while still maintaining a reasonably low-distortion sine waveform. Switching frequency ranges from about one switch Verification of a frequency scale Setting the output voltage through a second potentiometer Adjustment to minimize distortion of the sinusoidal signal Setting of the symmetry of the triangular signal 1Hz – 2MHz XR Function Generator Kit.
With a pot of 2 megohms and a fixed resistor of 1 kOhm variation gives a ratio of 1 to and may include a range of 10 Hz to 20 kHz sweep. For this project, I was more interested in producing a clean undistorted sinewave rather than pushing it to the limits in terms of frequency.
For measurement purposes in the electronics laboratory is needed again and again signals of different frequency and waveforms. The datashret must be adjustable and at least cover the low frequency range. The amplitude setting at pin 3 is connected with fixed resistors, so the output voltage is always the same.
It’s small, power efficient, yet customizable through onboard 2 x 7 perfboard that can be used for connecting various sensors and connectors.
Function Generator with XR2206
Many attempts have come out with this simple circuit. All required circuit details are shown in the datasheet. The actual sample structure differs in some details from the data sheet. At pin 3 to set the exact medium voltage and the output amplitude. Although datashet chip is in current production, both are still widely available – either as old stock or, perhaps, as ‘clones’.