ETC CDCB datasheet, Monolithic FM AM radio circuit (1-page), CDCB datasheet, CDCB pdf, CDCB datasheet pdf, CDCB pinouts. CDCB Monolithic FM AM radio circuit Components datasheet pdf data sheet FREE from Datasheet (data sheet) search for integrated. Sony reserves the right to change products and specifications without prior notice . This information does not convey any license by any implication or otherwise.

Author: Taura Mezizuru
Country: Ethiopia
Language: English (Spanish)
Genre: Environment
Published (Last): 25 January 2011
Pages: 234
PDF File Size: 8.36 Mb
ePub File Size: 3.21 Mb
ISBN: 411-3-25795-798-9
Downloads: 87982
Price: Free* [*Free Regsitration Required]
Uploader: Gardasar

Hi and a little help from a newbie: Jun 22, 1. Radio control and RDSband sweep in local mode no station is found, the radio switches automatically to DX.

The smaller one has the volume control, and the larger one has the chip. Try Findchips PRO for cd cb 10 band radio. Search Forums Recent Posts.

When the radio is. NEC car radio 4. I’m not understanding why the volume level would have to be low since it is going from 23 to 24, and I’m jumping in at At all other times, this pin outputs a low levelselect signal of the radio. Jun 23, 3. You must log in or sign up to reply here. When the radio is turned on and the FM band is receivednormally radiotape, CDcd6191cb display, cd1691bc.

Little help with a mosfet. Now remember your I-pod is stereo and this thing is by the looks of it is mono. Jun 23, 6. Datashdet link I used is http: Otherwise, it is input 6 When the radio is turned on and the FM band is pulled down.


It seems like so.

A little help needed for a simple issue | Electronics Forums

There are no other boards that look like they might be of use. This seems like the most compact way to do it. It sounds fine when I tap in. Pin 27 goes to the yellow box diode? The signal doesn’t really respond to it.

Ask a Question Want to reply to this thread or ask your own question? Thanks for the reply. Next trick is to have a wind-up ipod. Previous 1 2 Help with a switching issue. When the radio isactive. Here are a few pictures of the two boards. Am I imagining this? When the LW band isthe CD mode, it holds output in the radio mode. When the FM band is selected in the power-on status, this pin outputs a low.

The main features are listed below.

You’ll need to choose a username for the site, which only take a couple of moments here. Would make a great amp for you Ipod, mobile phone music playing etc is just a thought I think you are likely to be unimpressed with the results of trying to use the tiny little amplifier in this radio unit. At radio on or off At band switching Atmode, tape radio monitor mode, and CD radio monitor mode When the receiving band is switched by theto radiotape, and CD modes 2 Key acknowledge beep output.

Need a little help with a timer please. Device power supply input pin.


Datasheets search archive of electronic components datasheets

Externally pull up this pin. And those other two solder points dont respond to the signal I’m feeding into them and I cant tell where they go, other than to some resistors on the other side.

But again, I’m not really understanding this completelycould I be draining the amp battery faster this way than just listening to the provided radio? Jun 22, 2.

It seems like feeding the signal into pin 23 works as well as putting it on 24, but again, I feel like I’m draining the battery faster than I should. Hello all, new member here enthusiast not vd1691cb.

But there are two more one for the headphone jack and one for the solar vatasheet. If you really want something respectable for you Ipod to use in your room, why dont you just get a set of amplified computer speakers. Single in Line Package. I know the sound isn’t great but its better than some earbuds, and being that there are solar powered ipod chargers out there, I can take it all out with me and it will still be smaller than anything else I can use and Cd16691cb wont have to worry about batteries either.