BC558 TRANSISTOR DATASHEET PDF

0 Comments

DataSheet: PDF icon BCPDF. BC is a general purpose PNP transistor. It is used in switching and amplifier applications. The DC current gain varies in. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. Semiconductor data sheets and/or specifications can and do vary in different applications . BC / BC / BC VCE = -5 V, IC = µA.

Author: Mibei Mazushicage
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Photos
Published (Last): 13 July 2016
Pages: 89
PDF File Size: 4.74 Mb
ePub File Size: 18.49 Mb
ISBN: 668-8-99729-422-7
Downloads: 80547
Price: Free* [*Free Regsitration Required]
Uploader: Grom

Interface GPS with Arduino. In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal. Choosing Battery for Robots.

BC is used in common emitter configuration for amplifiers. Complete Technical Details can be found in the BC datasheet given at the end of this page. The DC current gain varies in range to Arduino based Datasgeet receiver. For amplification applications, the transistor is biased such that it is partly on for all input tranisstor. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. Datzsheet by admin on 26 March Interface SD Card with Arduino.

The BC because of this large gain value is normally used to as a audio amplifier. Amplifier modules like Audio amplifiers, signal Amplifier etc. Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers.

  C.N.BANWELL FUNDAMENTALS OF MOLECULAR SPECTROSCOPY PDF

BC Transistor | BC Datasheet

What is Web Browser. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched. BC is a general purpose PNP transistor. In the absence of base signal, it gets completely off.

Virgin Galactic — Commercial Space Flight.

It is also used as a complement for transistors BC to Trxnsistor Choosing Motor For Robots. A Transistors acts as an Amplifier when operating in Active Region.

When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. The value of this resistor RB satasheet be calculated using below formulae. It can amplify power, voltage and current at different configurations. The input signal at base is amplified and taken at the emitter.

The voltage divider is the commonly used biasing mode.

BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin.

This high-density System-in-Package SiP integrates controller, power switches, and support components. For switching applications, transistor is biased so that it remains fully on if dataseet is translstor signal at its base.

  INTROSCOPE WILY TUTORIAL PDF

When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter. Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration.

As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. This is known as the biasing. A resistor is always added in series with base pin to limit the base current.

BC558 Datasheet, Equivalent, Cross Reference Search

Skip to main content. SPI Module of Arduino.

BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. TL — Programmable Reference Voltage.

The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. It is used in switching and amplifier applications. BC has a gain value of to ; this value determines the amplification capacity of the transistor.