ASTM A666 PDF
L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked _机械 /仪表_工程科技_专业资料。ASTM A Standard.
|Published (Last):||26 August 2017|
|PDF File Size:||1.71 Mb|
|ePub File Size:||17.89 Mb|
|Price:||Free* [*Free Regsitration Required]|
An alternative method of determining? The steels shall adhere w666 specified chemical composition requirements. Only annealed conditions of grades speci? This abstract is a brief summary of the referenced standard. A superscript epsilon e indicates an editorial change since the last revision or reapproval.
Hard Elongation in 2 in. Material Test Report and Certi? ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Rockwell B 95 95 Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
The values obtained in this manner should not, however, be taken as the actual yield strength for 0.
Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use. A — 03 Standard Speci?
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Last previous edition approved in as A — Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
A number in parentheses indicates the year of last reapproval. D PSS means plate, strip, sheet.
ASTM-A Alloys | E. Jordan Brookes Company
Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending asym be determined. However, in the case of dispute, tests shall be made by pressure. B Maximum unless otherwise indicated. Link to Active This link will always route to the current Active version of the standard.
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
This standard has been approved for use by agencies of the Department of Defense. They shall be formed in different shapes such as sheets, strips, plates and ast, bars. The choice of test method for materials in conditions other than annealed shall be at the option of the seller.
The values given in parentheses are for information only. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.
ICS Number Code The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. In case of dispute, the offset method of determining yield strength aa666 be used.
If you feel that your comments have not received a fair hearing q666 should make your views known to the ASTM Committee on Standards, at the address shown below. This revision of Speci?
Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Originally approved in B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?
The noncontrolling factor normally will exceed considerably the speci? Number of Atm 8. This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions.
The values given in parentheses are for information only. HardC Elongation in 2 in. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.