ANSI A161.1 PDF
Buy ANSI A PERFORMANCE STANDARDS FOR KITCHEN AND VANITY CABINETS from SAI Global. Buy KCMA A Performance And Construction Standard For Kitchen And Vanity Cabinets from SAI Global. Kitchen and vanity cabinets bearing the ANSI/KCMA A certification seal have been extensively tested for their structural integrity, drawer.
|Genre:||Health and Food|
|Published (Last):||3 January 2013|
|PDF File Size:||14.15 Mb|
|ePub File Size:||19.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
To test the ability of the finish to withstand high heata cabinet door is placed in a hotbox at F and 70 percent relative humidity for 24 hours.
To test the ability of the finish to withstand substances typically found in the kitchen and bath, exterior exposed surfaces of doors, front frames, drawer fronts and end panels are subjected to vinegar, lemon, orange and grape juices, tomato catsup, x161.1, olive oil, and proof alcohol for 24 hours and to mustard for one hour. To test the ability of the finish to w absi hot and cold cycles for prolonged periods, a cabinet door is placed in a hotbox at F and 70 percent relative humidity for one hour, removed and allowed to return to room temperature and humidity conditions, and then placed in a coldbox for one hour at -5F.
These verify the structural integrity and strength of the cabinets. For information a1161.1 the certification or to locate a certified cabinet manufacturer, visit the Certifications portal at KCMA. The drawers must then remain operable with no failure in any part of the drawer assembly or operating system, and drawer bottoms must not be deflected to interfere with drawer operation.
Shelves and bottoms are loaded aansi 15 pounds per square foot to ensure no excessive deflection or joint failure on the cabinet or mounting system.
Scroll Down for more stories.
On all cabinets, the shelves and bottoms are loaded at 15 pounds per square foot, with the weight maintained for seven days to ensure that there is no excessive deflection and no visible sign of joint separation or failure of any part of the cabinets or the mounting system.
Anis test the ability of drawers and drawer mechanisms to operate with loading during normal a1161.1, drawers are loaded at 15 pounds per square foot and operated through 25, cycles.
For more information on the certification process, or to find manufacturers of certified cabinetry, visit KCMA. Have something to say? A hour soap and water solution test checks the finish’s ability to withstand exposure to detergents and moisture. A 3 pound weight is dropped 10 times against the drawer assembly to ensure that the drawer front assembly will withstand the impact of closing. A load of up to pounds is applied against the inside of cabinet fronts to ensure reliable front joints.
Doors are opened and closed for 25, cycles to ensure durability under the stress of normal usage. The door must remain weighted for 10 minutes, after which the door and hinges must show no visible signs of damage, and connections between cabinet-and-hinge and door-and-hinge must show no sign of looseness. To test the ability of doors, door-holding devices, hinges and attachment devices to operate under the stress of normal use, doors are opened and closed through a full degree swing for 25, cycles.
The cycle is repeated five times.
Welcome to our redesigned homepage! Drawers and drawer mechanisms are tested at 15 pounds per square foot and operated through 25, opening and closing cycles to assure durability. To test the ability of the drawer-front assembly to withstand the impact of closing the drawer under normal use, a 3-pound weight is dropped 8 inches against the drawer assembly.
The door edge must then show no delamination or swelling and no appreciable discoloration or evidence of blistering, checking, whitening, or other film failure. To test the ability of shelves, bottoms and drawer bottoms to withstand the dropping of cans and other items, a 3-pound steel ball is dropped from 6 inches above the surface.
The strength behind certified cabinetry: ANSI/KCMA A161.1
Installed wall cabinets are loaded with pounds to ensure that the cabinet nasi accept net loading in compliance with ANSI A Cabinets are impact tested by striking the center of a closed and open door with a 10 pound sand bag. The cabinet door must operate as before the test and show no damage or sign of separation or failure in the system.
The maximum number of products that can be compared is 4. To test the ability of cabinet doors and connections to withstand impacts such as children may cause in falling against a cabinet, or running into it with a tricycle, a pound sandbag is used to strike the center of a closed cabinet door and repeated with the door opened to a degree angle.
In order to be certified, cabinets must also undergo eight categories of testing, covering structural integrity, drawer and door operation and finish quality see sidebar below.
Mastercraft Cabinets | KCMA Certification Program, ANSI Standards
To test the ability of the finish to withstand long periods of exposure to a detergent and water solution, a cabinet door edge is subjected to exposure to a standardized detergent formula for 24 hours. This ensures the cabinets will live up to your expectations. Please refine your selection.
To be certified, cabinetry must first meet the following 14 construction requirements: They should also be filled and sanded, edgebanded, or otherwise finished to ensure compliance with the performance standards.
To test the strength of base-front joints, a load of pounds is applied against the inside of cabinet-front stiles for cabinets with a drawer rail, or pounds for cabinets without a drawer rail, to ensure reliable front joints that will not open during stress in service or during installation. The weighted door is slowly operated for 10 cycles from 90 degrees open to 20 degrees open, and returned to the degree position.
Skip to main content. A 3 pound steel ball is “drop tested” against shelves, cabinet bottoms and drawer bodies to ensure cabinets will withstand dropping of cans and other items. The exceptions are sink fronts and bases, oven cabinets and refrigerator cabinets. Cabinet finishes are inspected to ensure that stringent standards of appearance are also met. These tests create, in accelerated form, the cumulative effects of years of normal kitchen conditions of pre-finished cabinets.
After the test the drawer must not be damaged and must operate as before the test, with no visible sign of joint separation or failure of any part of the cabinet or mounting system. Cabinet doors are weighted with 65 pounds and operated 10 times to test the ability of door and hinges to withstand loading. The finish must then show no appreciable discoloration and no evidence of blistering, cold checking, or other film failure.