ALESIS MICROVERB 4 MANUALE ITALIANO PDF
Alesis Service Manual. B. ALESIS. MicroVerb 4 (C4). Service Manual. P/N: B. The information in this document contains. Documents, presets, manuals Alesis MicroVerb 4 – Audiofanzine. MicroVerb 4, Reverb from Alesis in the MicroVerb series. Service Manual V ALESIS. (Last edits & updates: 12/11/ ) MICRO SERIES; MICROVERB 3: MANUAL · PROGRAM CHART; MICROVERB 4: MANUAL · PROGRAM.
|Published (Last):||25 December 2007|
|PDF File Size:||15.19 Mb|
|ePub File Size:||7.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
Other Media Files : Alesis MicroVerb 4
ED turns from off to on in Programs 50, This is the tricky part but will be well worth the effort. Refer to the owner’s manual of your mixer or instrument amp if necessary.
Triggering is indksated the instant the green LED turns from off to oa Triggered alesix lend themselves most effectively to instmments with a sharp leading edge to their attack, like cymbal crashes or continuous percussive playing from drums or rhythm instruments electric rhythm guitar included.
Press any numbefed button from to 9. You should find a combinatbn of level settings that will provide an amazingly noise free over- all sound. You’ll be able to maintain spontaneity in your music while creating sounds as subtle or as dramatic as you like.
Not necessarily More subtle flanges can be manuqle simply by changing the mix ratio. Astun- ning alesiis studio effect fCNrmerty available only by laboriously flipping areei of reconjed tape over, playing It backwards and crossing your fingers.
Full text of “Alesis MidiVerb 2 Owner’s Manual”
Check the sectton titled Connectton s for the proper method of installatkyi with your system. To a IceytxMird, drum machine, guitar, or microphone effected signal to dry signal on the mixer by using the individual input channel faders dry signal and iraliano stereo effects returns effected signal from MV II.
The speed and width of this panning effect is different for each program. This resetting action momentarily intentipts the delayed signal during the reset and the thump- ing popping sound might appear. Because when applied to the right input signal the effect is fantastic!
Use this as a reference guide and starting point. Indicating man- ual Program change status. If you are using an instrument with a mono output guitar, mic, keyt pard. They do make a difference. You wilt see the num- ber 65 in the two digit LED display. The thumping sound is caused by volume fluctuations in the sustain portion of the sound that are causing the triggering action to reoccur.
Two stereogenerator programs create stereosignalsfroma mono source-great for that wkto keyboard sound when you don’t want to use reverb or chorua The last three programs are regenerated echoes that vary in decay time and the extent of their traifing echoes -and they are astonishingly deaa Program Search the history of over billion web pages on the Internet.
When you turn on the unit the program assigned to MIDI patch 01 will auto- matically be activated. This delay and pitch modulation is continu- ously varied by a lew frequency oscillator The effect creates changes over time in the frequency content of the mixed signal. The lower right segment of the two digit LED display will blink for approximately 4 seconds, prompting you to enter a second numt er.
For example, if you are connected to a mixer you will need to adjust the effects send s and receive s to the proper level, then set the master stereo output level of the mixer accordingly If you are connected to an instrument amplifier, you should adjust its volume control to the desired level. Press another number through 9. See your Alesis dealer. Convenient defeat of the effects signal through front panel buttons or through MlDLThis wortcs independently of the rear panel defeat jack.
If you are using an instrument with stereo outputs keytdoard, daim machine, etc. This completes the program change.
Adjust them accordingly and watch those LEDs. Check with your Alesis dealer. Here’s a setup procedure that you should follow closely: But, please thorougNy read this manual when you have time, so you won’t miss anything important. Because the envelope of such instalments is so short there will be no sus- tained signal present to be intemjpted by the trig- gering action at the onset of the next input signal.
When connected to a mixing board, set the MIX control to full on all effect. They are named Bkxxn and have an envefc pe that rises bkxxns to a rk: This will become the current program and will now be assignable to the MIDI patch number you just entered.
Documents, presets, manuals Alesis MicroVerb 4 – Audiofanzine
By adjusting the mix control you can vary the amount of perceived flanging and panning to suit your needs. With explosive sounds like drums and percus- sion or heavy pounding electric guitar that have very sharp attacks and quick decays, the trig- gering action occurs every time the signal hits the input of MIDIVERB II.
Then check the other level controls in your system again. These levels will vary depending on the actual equipment used, but should fail somewhere in the shaded areas.
Each program varies in tonal characteristics and decay time. You might have to adjust other levels in your system at this time. In general, smaller sounding spaces with smoother articulation of the reverb decay will provide the proper range of ambience for full dnim kits and rhythm section instrumenta The larger spaces wHI lend themselves readily to vocals and lead instruments.
Use your own judgment and taste. Sending MIDI patch number will call up the defeat program. This jack accepts any standard connection of any in8trunr ent or mk: Instruments with a snrxxith, continuous decay such as key- boards or lightly strummed laesis might retrigger ttie flange during the sustain portkxi of their sound. If you do hear much noise you should check your source to make italiaho you have a strong, clear output signal.
You should hear very little, if any, background noise. Make sure you are sending a strong, clear signal to the unit.