Reference Manual. INTRODUCTION Thank you for purchasing the Alesis ADAT- XT Digital Multitrack Tape Recorder. To take full advantage of the XT’s functions, . User manual for the device Alesis ADAT-XT. Online user manual database. musical instrument, dj equipment manuals, user guides, spec sheets. Alesis ADAT-XT Recording Equipment User Manual. Page 1. Page 2. Page 3. Page 4.

Author: Gokinos Malalar
Country: Zimbabwe
Language: English (Spanish)
Genre: Health and Food
Published (Last): 15 August 2018
Pages: 108
PDF File Size: 19.14 Mb
ePub File Size: 9.5 Mb
ISBN: 721-7-56252-999-8
Downloads: 39364
Price: Free* [*Free Regsitration Required]
Uploader: Kekora

Alesis ADAT-XT user manual

OversamplingThe process of taking more samples than is required in order to more accuratelyreconstruct a digitized signal back into analog audio. Therefore, where applicable you will need to refer to other sections of this manual for instructions on how to setup the XT for a particular job. During power-up, the XT checks the footswitch to determine whether it isnormally open or normally closed manula, and calibrates itself accordingly.

For your convenience If looking through the Alesis ADAT-XT user manual directly on this website is not convenient for you, there are two possible solutions: The XT,however, maintains a constant offset between them. They indicate that the parameter for which they are named has been selected or turned on.

Do notoperate the unit.


Page 32 Chapter 3: Transport Buttons Chapter 2: The currently selectedmode may be amnual by observing the peak meters themselves. In this tutorial, we will berecording from the analog audio inputs at the start of the audio portion of the tape 0: The digital representation of the data as stored on tape was therefore invertedrelative to the analog input i.

  IPC D 300G PDF

Turn on the power without installing a tape. When you install it, keep in mind that heat is the major enemy ofelectronic equipment.

Remote meter display for the m20 professional bit digital recording system 9 pages. Basic Operations automatically recognizes the shorter length of the ST because the hubs used in the cassette are larger. Error message 8 normally occurs when the tape reaches the end while formatting or recording. Er 0 Tape Load Error: Recording While Formatting Chapter 4: During the operation, the tape willhalf-eject twice. It is caused by the fact that the XT cannot readtiming data from the leader.

Alesis Sync Cables are available in threedifferent lengths: Page 68 Chapter 5: Types of outputs varyin connector type, level, use sends, monitor, mixand electrical characteristics impedance, balanced or unbalanced.

No user adjustment isnecessary. Chapter 5protocol which the XT uses, and vice-versa.

The Marketplace for Musicians |

Page 83 Tape a note to the top of the unit describing the problem, include your name and a phone number where Alesis can contact you if necessary, as well as instructions on where you want the product returned. This is useful when you want toprecisely punch in to a specific place on one or more tracks.


Larger Key Notch Note: For more info about locating and editing Locate Points, see page Page 30 Chapter 3: These are compatible with lowimpedance, unbalanced, dBV outputs typical of equipment such as mixers,synthesizers, samplers, direct boxes, etc. Synchronization requires a dual male, 9 pin D connector cable for each slave to be synchronized.

Page 62 Chapter 5: Digital signals for the same 20 kHz audio requires a frequencyresponse of several million Hertz.

Page 86 Appendix D: GlossaryNOOutputA path through which audio passes from one device to another. The larger of the two outer key maual is at the bottom.

Insert the tape into the transport. Get familiar with them by using them while watching the TIME counter. Page 54 Chapter 4: Crossfading always begins at the punch point and continues for the amount of timeyou have specified.

mabual The track copies will be an exactduplicate of the original i. For more information on using the Track Copy function, see page What it comes to is this: