57DP-12-2C2 RELAY PDF

0 Comments

RELAY 57DP 1C6 24V. RELAY 57DP 1C6 6V. RELAY 57DP 1C/O 24V OEN. RELAY 57DP2C2 12V. RELAY 57DP 2C2 16V. RELAY 57DP 2C6 24V. RELAY. Supply Of Oen Relay 57DpV-2C Make- Oen/Pla/Omron. Details As Per Annexure-A. | Due date: 28 Jun, | Tender work Value. 57DPB2 57DPB6 57DPA2 57DPA6 57DPC2 57DPC6 57DPA2 57DPC2 57DPC6 57DPC2 57DPC6 57DPB2 57DPB6 Description, MINIATURE POWER RELAYS.

Author: Shakora Daisho
Country: Austria
Language: English (Spanish)
Genre: Music
Published (Last): 5 July 2014
Pages: 183
PDF File Size: 16.80 Mb
ePub File Size: 4.56 Mb
ISBN: 754-4-87835-372-4
Downloads: 24245
Price: Free* [*Free Regsitration Required]
Uploader: Manos

There is some mechanical blockage with the external encoder.

Sign Up to Newsletter

Maximum Speed This is the maximum spindle that the user can use in a NC part program block. After selecting an axis, enter the number of the desired parameter using the numeric keypad or the delay and down arrows to scroll through the available parameters, then press ENTER to view that specific parameter.

These are the same commands used for internal Tool Offsets. The Relaay Parameter set is designated as SAx. Therefore, the sign of any position value will be ignored. Refer to the drive firmware HELP file or documentation for details. The bipolar 57dp1-2-2c2 limit value determines the maximum allowable torque in either direction. If the programmer does not enter a Feedrate in this NC Block, it will be executed using the last feedrate value used for a positional move.

This G08 command must be preceded by a G62 without lag command In an ideal situation, once a G08 command has been issued the drive will continue to move until the position reading from the external encoder is equal to that of the G08 command. This positioning menu allows movement to be programmed in either an Absolute G90 or an Incremental G91 mode.

Substituting any other Floating Point register in the above data string will send the data to the Floating Point register that corresponds to the Tool Correction register for the desired axis. Parameters that are listed with a number can be selected by the numerical keypad on the CTA or by using the up 57rp-12-2c2 down arrows.

  INTRODUCTORY ECONOMETRICS RAMU RAMANATHAN PDF

The direction in a G91 move is always determined by the sign of the programmed incremental distance. To disable the CTA, follow the same procedure. If you want Spindle positioning without a spindle encoder, but with a Home limit switch instead, relaj this bit to 1.

B-7 Parameter Data Subclass Stop from the Primary Function selection screen to begin this NC program block. When the output is correctly acknowledged the program progresses to the next NC Block. This situation may occur in slide units, both during manual operation, when the Reverse input is triggered, and during automatic operation when the Homing input is triggered.

G62 is a modal value, however, it is recommended that G61 always accompany a G69 move for clarity and certainty. The maximum value allowed is limited by axis parameter Aa15 Tool Correction. Positive Stop Feedrate Aa20 contains the maximum feedrate that can be programmed when executing any positive stop functions. This parameter defines the starting point of slip increase.

This should be avoided. Four appendices are also provided for: When jogging, the axis will also be stopped at a distance 2 times the position window away from the overtravel limit.

General suggestions for improving cycle time: After the switch settings are changed, you must re-cycle power to the digital drive for the switch settings to take effect.

The block will be stored and any previous data in N is permanently deleted. This is commonly utilized with rotary axis applications where hydraulic clamping mechanisms are used to maintain the stability of high mass drive-trains rather than risk motor overload during cutting. These two values are summed and placed into S Position Feedback 2, Reference Distance as the value to be displayed when at the Home position.

The user should enter the speed value to be used for positioning the spindle. This is a requirement encountered in the commissioning of machines using 57do-12-2c2 feedback devices.

This parameter gives the user that ability. If set to 0, further deflection of the scale will cause the position value to increase in the positive direction. This particular block is waiting for an Acknowledgment Output to be acknowledged before proceeding to the next block. This will allow the user to position the axis within the rotation of the tool. See note below for Rotary operation.

  KODAK EASYSHARE M820 MANUAL PDF

The table below shows the proper addressing for externally entering data into the standard Tool Correction registers. Only one axis is allowed per G69 operation. If the value in the parameter is and you want to change only the LSB from a 1 to a 0, you must send down In absolute positioning G90all movements of the slide are made to some absolute distance from the machine reference position, which will either be Home or some offset position from Home.

B-7 Parameter Lists Subclasses If the cam search direction was negative: If this bit is set to 1, with a positive speed command, the motor will turn counterclockwise CCW.

A-4 Settings Menu – Serial Communication Enter the value to be used for this parameter. The DC bus output is checked in the drive as to whether it has exceeded this value. The checksum for the data string must still be sent with the data.

Tender for Supply Of Oen Relay 57DpV-2C | Tenders in Kharagpur – West Bengal

Moving the cursor to the desired option or pressing the numerical key associated with the desired option will step the user into the appropriate parameter set. When set to 1, monitoring of the 57dp-1-22c2 encoder not is not active Bit In practice, it is very difficult to calculate how all of these timing factors interact. The user is guided through a series of screens that displays the available functions.

This command is necessary when the user has completed a move using either the G37 or G38 command and they want the next series of moves to be executed using the shortest path mode.